30% OFF EVERYTHING · CODE NOVEMBER30 · ENDS 11/30
Third-Party Tested
COAs Published
Same-Day Fulfillment
US Based

Purity vs Identity: What HPLC and Mass Spec Tell You

Published

A certificate of analysis (COA) for a research peptide should answer two separate questions. First: is the compound in the vial the peptide it claims to be? Second: of the peptide material in the vial, how much is that one compound?

The first question is about identity. The second is about purity. They are answered by different tests, and a good result on one says very little about the other. If you are comparing vendors, knowing the difference is the quickest way to tell a thorough COA from a thin one.

What purity testing measures

Purity is usually measured by HPLC (high-performance liquid chromatography). The lab dissolves a small sample and pushes it through a packed column. Different molecules travel through the column at different speeds, so they come out at different times.

A detector at the end records each molecule as it comes out, and the result is drawn as a chart called a chromatogram. Each compound shows up as a peak. The target peptide should be one large peak. Leftovers from synthesis, such as shortened or damaged versions of the peptide, show up as smaller peaks around it.

The purity figure is the area of the main peak as a share of the total area of all the peaks. A result of 98% means that 98% of the material the detector saw came out as that one main peak.

What purity testing can't tell you

  • Whether the main peak is the right peptide. HPLC purity measures how clean a sample is, not what it is. A vial holding the wrong peptide can still come back 99% pure.
  • Anything the detector doesn't see. Water and salts don't show up as peptide peaks, so they are not counted against purity.
  • How much peptide is in the vial. That is a separate number, net peptide content, covered in our guide to reading a peptide COA.
  • Impurities hiding under the main peak. If an impurity leaves the column at almost the same time as the target, the two can overlap and be counted as one.

What identity testing measures

Identity testing checks that the main compound is the peptide named on the label. There are two common ways to do it.

Mass spectrometry (MS) weighs molecules. Every peptide has an expected molecular weight, worked out from its amino acid sequence. The lab measures the mass of the compound in the sample and compares it with that expected value. A close match is strong evidence the right molecule is there. A mismatch means it isn't.

HPLC retention time matching compares the sample with a reference standard, a known sample of the correct peptide. If the sample's main peak comes out of the column at the same time as the standard's, that supports a match.

Some labs combine the two in one run, called LC-MS: the HPLC separates the sample and the mass spectrometer weighs what comes out.

What identity testing can't tell you

  • How pure the sample is. A correct mass shows the right molecule is present. It doesn't show how much else is present alongside it.
  • The exact order of the amino acids, from mass alone. Two peptides built from the same amino acids in a different order weigh the same, and so do some amino acids that differ only in shape. A single mass reading can't tell them apart.
  • A unique answer, from retention time alone. Two different compounds can come out of the column at the same time. Retention time matching is only as good as the reference standard it is compared against.

Why a COA needs both

Each test covers the other's blind spot. Purity without identity could describe a very clean sample of the wrong compound. Identity without purity could describe the right compound mixed with a lot of something else.

PurityIdentity
The question it answersHow much of the peptide material is the target compound?Is the main compound the peptide on the label?
Typical methodHPLC with a UV detectorMass spectrometry, or HPLC retention time against a reference standard
How the result looksA percentage, checked against a specification such as ≥95%A measured mass next to the expected mass, or confirmed / pass
What it missesWhether the compound is the right oneHow much other material is in the sample

What to look for when comparing vendors

  • Both tests on the certificate. A purity percentage with no identity result answers only half the question.
  • A named method for each. "Purity: 99%" means more when it says HPLC, and "identity confirmed" means more when it says how.
  • A specification and a result. Each test should show what it was required to meet and what it actually measured.
  • A lot number. Both results should be tied to the batch the vial came from.

For a line-by-line walkthrough of a full certificate, and the red flags that suggest a COA can't be trusted, see How to Read a Peptide Certificate of Analysis.

Apex Labs certificates

Our published certificates of analysis are on the Lab Results page.

All Apex Labs products are sold strictly for laboratory research use only. They are not for human or animal consumption, and nothing on this page is medical advice.